Notifier Fcm-1-rel | Notifier | Accessories | Gasdetectorsusa
Gas Leak and Flame Detectors, Analyzers, Alarm Devices and Calibration Gas

NOTIFIER   FCM-1-REL

SKU# (4143)
NOTIFIER FCM-1-REL
  • DESCRIPTION
  • FEATURES
  • SPECIFICATIONS
  • LITERATURE
Notifier FCM-1-REL(A) Series Releasing Control Module for fire suppresion releasing applications. Reports the panel status as NORMAL, OPEN or SHORT CIRCUIT. Analog communications. FlashScan operation. 15 to 32 VDC. UL, FM and CSFM Approved.

Please Email us your request for quote   

   4 Weeks  ]

The FCM-1-REL Releasing Control Module is specifically designed for fire suppression releasing applications in FlashScan® systems. Power to the release agent solenoid(s) runs through the module for full-time monitoring and supervision.

The FCM-1-REL Releasing Control Module uses a redundant protocol; the module must be armed with a pair of signals in order to activate. It will then enter a 3-second window awaiting a pair of confirmation signals. If no confirmation is received, the module will automatically reset. It also supervises the wiring to the connected load and reports the status to the panel as NORMAL, OPEN, or SHORT CIRCUIT. The module has two pairs of output termination points available for fault-tolerant wiring and a panel-controlled LED indicator. The module may be connected to either one 24VDC solenoid or up to two 12VDC solenoids (in series). To ensure proper operation, this module shall be connected to a compatible Notifier system control panel only (list available from Notifier). In addition, please refer to Notifier Device Compatibility Doc- ument PN 15378 for the list of compatible solenoids.

NOTE: FCM-1-REL is required for all new FlashScan-mode releasing applications with NFS2-3030 (version 14.0 or higher), NFS2-640 (version 12.0 or higher) and NFS-320(E)(C) (version 12.0 or higher) panels. Use FCM-1 for releasing applications on NFS-640, NFS-3030, and all CLIP mode panels.

FEATURES

  • Redundant protocol for added protection
  • Configurable for Class A or Class B operation
  • External supply voltage monitoring
  • Can power one 24V or two 12V solenoids
  • SEMS screws for easing wiring
  • Panel controlled status LED
  • Analog communications
  • Rotary address switches
  • Low standby current
  • Mounts in standard 4" (10.16 cm) junction box
  • FlashScan operation
Agency Listings and Approvals

These listings and approvals apply to the modules specified in this document. In some cases, certain modules or applications may not be listed by certain approval agencies, or listings may be in process. Consult factory for latest listing status.

  • UL: S635
  • ULC: (FCM-1-RELA)
  • FM Approved
  • CSFM: 7300-0028:0249

FCM-1-REL(A) SPECIFICATIONS
GENERAL SPECIFICATIONS
Operating voltage: 15 to 32 VDC
Communication Line Loop Impedance: 40 Ohm max.
Temperature Range: 14°F to 140°F (-10° to 60°C)
Relative Humidity: 10% to 95% noncondensing
Shipping Weight: 5.5 oz (156 g)
Drain on external supply: 1.7 mA maximum using 24 VDC supply; 2.2 mA Maximum using 80 VRMS supply.
Dimensions: 4.275" W × 4.675" H × 1.400" D (10.86 cm W × 11.87 cm H × 3.56 cm D)
SLC
Average Operating Current: 700 μA max @ 24 VDC (one communication every 5 sec. with LED enabled)
Maximum Activation Current: 9.0 mA (LED on)
EXTERNAL SUPPLY
Normal Operating Voltage: 24 VDC Nominal
Maximum Line Loss: 2.3 VDC (total allowable loss from power supply to module and from module to solenoid)
Minimum Operating Voltage to Activate Solenoid: 18 VDC (at solenoid)
Standby Current: 6.4 mA
Activation Current: 10 mA
SOLENOID
Supervisory Loop Voltage: 3.3 V
Supervisory Loop Current (Normal) 30mA
Maximum Activation Current: 2 A
Export Info
Made inMexico

 Info/Quote Request
 Reseller & Volume Discounts
 Shipping Rates

B2B Checkout Options: Designated Carrier and Tax-Exempt purchase
Payment Options: Credit Card, Credit Card Over the Phone, PAYPAL, Wire Transfer/Electronic Payment and Check

Checkout with Paypal Visa MasterCard Amex Checkout with Wire Transfer Electronic Payment

> NOTIFIER :    42 Items found.
HS-NCM-MF__
(4326)

NOTIFIER  HS-NCM-MF

Notifier HS-NCM High-Speed Network Communications Module. Single or Multi-mode versions available. Allow connection from Notifier Panels to NOTI•FIRE•NET with a fiber-optic cable or twisted-pair wire. NFPA Style 4 (Class B) or Style 7 (Class A) operation. 24 VDC, 100Mb baud transmission rate. UL, ULC, CSFM and FM approved.

CPU2-3030D
(6931)

NOTIFIER  CPU2-3030D

Notifier CPU2-3030D Central processing unit for an NFS2-3030 system. Keypad/display installed; includes 640-character backlit LCD display, QWERTY programming and control keypad. Requires an AMPS-24(E) power supply.

Page: 1 | 2 | 3 | All
Cookie Notice

This online store uses cookies to remember users, enable checkout and to collect aggregate information that allows us to analyze traffic patterns on our site (no personal information is stored). For more information you can read our Privacy Policy.