Honeywell Fs24x-211-21-1 | Quadband Triple Ir | Flame Detectors | Gasdetectorsusa
Gas Leak and Flame Detectors, Analyzers, Alarm Devices and Calibration Gas

HONEYWELL   FS24X-211-21-1

HONEYWELL FS24X-211-21-1
  • DESCRIPTION
  • FEATURES
  • SPECIFICATIONS
  • LITERATURE
Honeywell Fire Sentry FS24X Series 211 Multi-Spectrum QuadBand Triple IR Fire and Flame Detector for hydrocarbon and non-hydrocarbon fires in all enviromental conditions. 110° field of view. With WireBand Technology, RS-485 ModBus communication and non-isolated 4-20 mA analog output. Includes alarm, fault and fire verification relays. FM, ATEX and CE mark approvals *** Phased Out *** Replaced by FS24X Plus [sku 7141]

Inquiry

Fire Sentry FS24X is a quantum leap in flame and fire detection with its sophisticated software and detection technology.

The Fire Sentry FS24X is the latest generation high technology Multi-Spectrum Triple IR (IR/IR/IR/Visible) Fire and Flame Detector, which is part of our FSX family of advanced technology Electro-Optical fire detectors. Using our patented* WideBand IRTM, WideBand 4.3 micron IRTM, and Visible detection technology, the Fire Sentry FS24X is a quantum leap in flame and fire detection. Sophisticated software algorithms and dual microprocessors ensure that the Fire Sentry FS24X has the highest fire detection performance combined with optimal false alarm rejection.

FEATURES

  • Patented* WideBand IRTM Technology
  • Patented* Electronic Frequency AnalysisTM
  • Visible Sensor for optimum false alarm rejection
  • Selectable detection sensitivities
  • Field-of-View: 110° full 100% cone-of-vision
  • Dual microprocessors for reliable performance
  • Real-time clock for accurate time dating of events
  • FirePicTM — pre-fire event data storage
  • Event log with date and time stamp
  • RS-485 ModBus communication
  • Non-Isolated 4-20 mA Analog output (sink or source)
  • Alarm, Fault and Fire Verification relays
  • Automatic optical path and electronic self-test
  • Widest operating temperature range
  • Patented* Electronics Module for components protection with easy plug-in terminations and field installation
  • Two 3⁄4” NPT OR 25mm conduit entries
  • Low power consumption
  • High RFI and EMI immunity
  • FM, ATEX, CE mark approvals
  • Meets SIL 2 requirements
BENEFITS

  • Detects hydrocarbon and non-hydrocarbon fuel fires in all environmental conditions
  • User selectable outputs
  • Optimal false alarm rejection for all environmental conditions
  • Minimal maintenance for trouble-free operation
  • PC software and Interface Module (FSIM) for fault diagnostics, real-time graphics (RTGs), and downloading of FirePicsTM and event log
  • Suitable for a wide variety of applications
  • Easy electronics module replacement
  • Test lamps for manual testing
APPLICATIONS

  • Refineries and Oil Production Facilities
  • Off-Shore Platforms
  • Turbine/Compressor Enclosures
  • Oil & Gas Pipelines and Pumping Stations
  • LNG/LPG Loading & Unloading Facilities
  • Natural Gas and CNG Plants
  • Ethanol, Methanol, and IPA Production and Storage
  • Crude Oil and Gasoline Storage and Tank Farms
  • Aircraft Hangars
  • Hydrogen Plants and Storage
  • Paint & Solvent Storage
  • Chemical Production, Storage, and Loading Facilities
  • Power Plants

The WideBand IRTM Infrared technology using high-speed solid-state Quantum sensors allows detection of all types of fires, hydrocarbon and non-hydrocarbon, in all weather conditions. If the detector’s signal is blocked by ordinary window glass, the patented WideBand IR sensors will still alarm to the fire but at a reduced sensitivity and slower response time.

Dual microprocessors provide a high level of fail-safe operation combined with fast and reliable performance. The Master Microprocessor performs high- speed digital sampling and signal-processing calculations; while the slave microprocessor handles various sensor data, performs communications, self- diagnostics and provides interface versatility; and additional memory for storing Event Log and FirePicTM data.

The Fire Sentry FSX family of detectors feature our patented* FirePic data storage and information retrieval facility. FirePicTM records pre-fire data, which can be recovered from the Detector’s non-volatile flash memory for post fire analysis and postulation of the fire cause. Additionally, unique Real-Time Graphing (RTGTM) allows viewing of the data which the Detector actually sees. A combination of outputs makes the Fire Sentry FS24X a truly versatile detector for today’s demanding industrial requirements.

The Fire Sentry FS24X detector has a detection range greater than 200 feet (Very High Sensitivity setting) for the detection of a one square-foot Heptane reference fire and has a cone of vision far greater in volumetric coverage than any other Multi-Spectrum IR Detector. This means fewer Detectors can be used as compared to other manufacturers’ Detectors.

Fire Sentry FS24X SPECIFICATIONS
Field of View 110° Full 100% Cone of vision, ± 55° from on axis
Sensitivity Very High, High, Medium and Low — Switch Selectable
Response Time 3-5 Seconds to 1 sq. ft. n-Heptane fire at 100 ft.
3-10 Seconds to 1 sq. ft. n-Heptane fire at 200 ft.
Spectral Sensitivity Visible: 400 – 700 nanometers
Near Band IR: 0.7 – 1.1 microns
Wide Band IR: 1.1 – 3 microns
Wide Band IR: 3.0 – 5.0 microns
Operating Voltage 24 VDC nominal (18-32 VDC) - Regulated
Power Consumption Operating: 56 mA @ 24 VDC nominal
Alarm: 106 mA @ 24 VDC nominal
Heater: 155 mA – additional
Note: Heater will turn on at 0oF (-17oC)
Output Relays Fire Alarm: SPDT (NO / NC) – De-Energized/Energized, Latching/Non-Latching
Fault: SPST (NO) – Normally Energized, Latching/Non-Latching
Auxiliary: SPDT (NO / NC) – De-Energized/Energized, Latching/Non-Latching
Contacts rating: 1 amp @ 24 VDC
Analog Output 0 - 20 mA stepped - Source or Sink User Selectable
Loop resistance 50 - 400 Ohms
Communication One of the following – User Selectable:
RS-485, ModBus Protocol
RS-485, FireBus II
HART, Optional plug-in module
Visual Indications Blue LED: Power
Red LED: Alarm
Yellow LED: Fault
Temperature Range Operating: -40 to +185oF (-40 to +85oC)
Storage: -67 to +230oF (-55 to +110oC)
Humidity Range 5 to 98% relative humidity, non-condensing
Vibration Meets or exceeds MilSpec 810C Method 514.2, Curve AW12
Wiring 14 AWG (2.5mm2) to 22 AWG (0.326mm2); Shielded Cable Recommended
Conduit Entries Standard: Two 3⁄4” NPT or two M25
Enclosure Materials Copper-Free Powder Coated Aluminum or 316 Stainless Steel
Enclosure Type NEMA 4 & 4X, IP66
Certifications FM: Class I, Div. 1 & 2, Groups B, C, & D; Class II, Div. 1 & 2, Groups E, F, & G; Class III
ATEX: II 2 G D; Ex d IIC T4 (Ta: -40 to +110oC), T5 (Ta: -40 to +75oC), T6 (Ta: -60 to +60oC)
CE: Complies with EN6100-6-4 & EN50130-4
SIL Rating: FMEDA is available upon request
Shipping Weight Aluminum: 3.6 lbs (1.6 kg)
Stainless Steel: 7 lbs (3.2 kg)
Mounting Swivel Bracket Assembly - Optional
Warranty Three years from date of shipping
Export Info
Made inUnited States
Harmonized Tariff Code (HTC)90318099
> ACCESSORIES - RELATED - CONSUMABLES :    8 Items found.
FVR-01
(4601)

HONEYWELL  FVR-01

Honeywell FVR-01 Field of View Restrictor for Honeywell Fire Sentry FS24X, FS20X, SS4, SS2, and FS10 Flame Detectors. PVC construction with steel circle clamp.



$182.48 
SH-001
(4467)

HONEYWELL  SH-001

Honeywell Fire Sentry SS4 Sunshield for SS2, SS4, FS20X & FS24X Detectors, 316 Stainless Steel



$242.61 
SM4
(3280)

HONEYWELL  SM4

Honeywell Fire Sentry SS4 Swivel mount For Fire Sentry FS24X, FS20X, FS10, SS4 and SS2 Flame Detectors



$318.30 
DASA1-P
(4604)

HONEYWELL  DASA1-P

Honeywell DASA1-P Air Shield for Honeywell Fire Sentry FS24X, FS20X, FS10, SS4 and SS2 Flame Detectors. Accepts 1/4" O.D. nylon tubing.



$637.63 
FSX-A014R
(4328)

HONEYWELL  FSX-A014R

Honeywell Optional HART module for FS24X detectors (factory installed)



$702.95 
FSX-A001
(4607)

HONEYWELL  FSX-A001

Honeywell FSX-A001 Interface for Fire Sentry FS24X and FS20X Flame Detectors. Converts RS-485 to USB and includes a USB driver. *** Phased Out ***



$1,006.73 
TL-1055
(2939)

HONEYWELL  TL-1055

IR test lamp for testing FSX detectors, non-explosion proof version. Incl universal charger



$2,130.62 
TL-2055
(2985)

HONEYWELL  TL-2055

HONEYWELL Class I, Div. 1 approved explosion-proof Test Lamp (flame simulator) for testing Fire Sentry FSX, FS24X (IR3) and FS20X (UV, IR and IR/UV) Flame Detectors externally in a hazardous location. Flame detectors that detect at 185-235 nm UV, near IR, wideband IR and 4.4 u IR radiation. The hand held Test Lamp comes with a Universal Charger (110 VAC and 220 VAC).



$4,105.03 
> QUADBAND TRIPLE IR :    2 Items found.
FS24X-911-21-5
(1989)

HONEYWELL  FS24X-911-21-5

Honeywell Fire Sentry FS24X Series 911 Multi-Spectrum QuadBand Triple IR Fire and Flame Detector for hydrocarbon and non-hydrocarbon fires in all enviromental conditions. 90° field of view. With WireBand Technology, RS-485 ModBus communication and non-isolated 4-20 mA analog output. Includes alarm, fault and fire verification relays. FM, ATEX, CE and INMETRO mark approvals

Configure

$4,371.15 
FS24XP-ANGXX
(7141)

HONEYWELL  FS24XP-ANGXX

Honeywell FS24X Plus IR3 Flame Detector for detection of hydrocarbon and hydrogen fires. Includes high visibility status LED, SM4 mount and multiple outpts: 4-20mA, relays, HART and Modbus. 24 VDC. ATEX, IECEx, cFMus (Class I, Div 1, Groups A,B,C,D), INMETRO, SIL2, FM3260 and EN54-10 Approvals. IP66 / IP67 (NEMA 4X).

Configure

$5,062.18 
Cookie Notice

This online store uses cookies to remember users, enable checkout and to collect aggregate information that allows us to analyze traffic patterns on our site (no personal information is stored). For more information you can read our Privacy Policy.